Статті
Постійне посилання на розділhttps://dspace.nuft.edu.ua/handle/123456789/7372
Переглянути
5 результатів
Результати пошуку
Документ Energy parameters of the process of ultrafine grinding og medical and cosmetic components in the bead mill(2021) Hrininh, Kateryna; Gubenia, Oleksii; Chepeliuk, OlenaThe process of ultrafine grinding of components of medicines and cosmetics in a laboratory bead mill is considered. The purpose of the study is (1) to determine the energy parameters of the process of ultrafine grinding of medicinal and cosmetic components in a bead mill, as well as (2) to determine the dependences of changes in technological parameters. A suspension of castor oil and cosmetic pigment in a ratio of 60% oil and 40% pigment was used as a model body. A series of experiments was carried out, where the degree of grinding was determined using a microscope with a built-in camera and software, the temperature was measured with ds18b20 temperature sensors, the power was measured with a three-phase CNFAJ Intelligent Power Meter. When grinding the pigment "red 120" for a period of time from 0 to 45 minutes, the power decreases, the temperature of the "beads-product" system increases, and the particle size decreases. This process occurs most intensively in the first 5 minutes. Most of the energy is spent on the work, which is spent on mixing the system "beads-product", and the work, that is spent on heating the structural components of the product and the parts of the mill interacting with them, which, in turn, depend on rheological properties of the suspension.Документ Energy parameters of ultrafine grinding of pharmaceutical and cosmetic ingredients in the bead mill(2020) Hrininh, Kateryna; Gubenia, OleksiiThe energy parameters of the grinding process of the components of pharmaceutical and cosmetic preparations in a bead mill are considered. The purpose of research - to determine the energy parameters of ultrafine grinding of pharmaceutical and cosmetic ingredients in the bead mill. A series of experimenters was conducted where the degree of grinding was measured using USB Digital Microscope and software, the temperature was measured with a TPM-10 electronic thermometer, and the power was measured with a CNFAJ Intelligent Power Meter three-phase wattmeter. As a result of the study, we can conclude that most of the energy is spent on the work of mixing the beadproduct system and the work spent on heating the structural components of the product and the interacting parts of the mill, which, in turn, depend on the rheological properties of the suspension.Документ Formation of suspension structure in the process of grinding in bead mills(2020) Hrininh, Kateryna; Gubenia, Oleksii; Telychkun, YuliiaIt has been investigated the rheological properties of the suspension of farmaceutical and cosmetics preparates during grinding at an experimental laboratory bead mill of periodic action. The rheological characteristics have been investigated on a rotary viscometer Reotest 2. as a result of the research, the flow curve of the suspension during grinding has been constructed and it has been found that within the investigated range the product does not change the character of flow regardless of measurement time and temperature. Analysis of the curve of the suspension during grinding revealed features which explain formation of the structure. The dependence of the effective viscosity on the shear rate during grinding of the suspension is polynomial and confirms the non Newtonian character of the product and is defined as a linear plastic body. The investigated finished product has 6.5 time’s higher viscosity in relation to pure castor oil, which is explained by the high dry matter content (40 %) and the increase in the newly formed area. The viscosity of the suspension varies depending on the temperature: cooled to 20 °C, the finished product has a viscosity of 22.5% higher than immediately after the grinding process with a temperature of 34 °CДокумент Investigation the process of superfine grinding of components of pharmaceutical and cosmetic products on the bead mill(2018) Hrininh, Kateryna; Hordeichuk, Ruslan; Gubenia, OleksiiThe process of grinding the components of pharmaceutical and cosmetic preparations in a bead mill is considered. The degree of grinding was measured with a "Klin" grindometer, the temperature was measured by a contactless pyrometer, the power was measured by current clamps. The smaller the particle size and the higher density of the suspension, the greater the energy required to conduct the process, and the more heat will be released. When grinding titanium dioxide over a period of 0 to 30 minutes, the power increases from 205 to 209 W, with the most intensive increase observed in the interval from 5 to 10 minutes at 2.33 W. In addition, the temperature of the suspension increases from 21.9 to 23.4 °C, the density of the suspension increases from 889 to 1176 kg/m3, and the particle size decreases from more than 100 μm to 10 μm, the most intensive grinding in the first 5 minutes of the process. When the quinacridone red Red 122 is grinded, the power is increased from 205 to 210 W, the slurry temperature is from 22.4 to 24.3 °C, the density is from 870 to 952 kg/m3, and the particle size decreases from more than 60 μm to 2 μm, while the most intensive grinding occurs in the first 5 minutes of the process.Документ Comparative analysis of equipment and research the superfine grinding process of titanium dioxide and quinacridone red suspensions in the bead mill(2018-06) Hrininh, Kateryna; Hordeichuk, Ruslan; Gubenia, OleksiiIntroduction. Analytical and experimental research was conducted to improve the process and equipment for the superfine grinding of medicinal and cosmetic preparations. Materials and methods. On the basis of modern scientific literature and own experience was given a comparative analysis of modern equipment for ultra-fine grinding. In the investigation are used suspensions of titanium dioxide and quinacridone red 122 with the vaseline oil. Results and discussion. Among the recommended installations, the most versatile, productive, compact, energy saving, with high degree for grinding (up to 1 microns), effective in the process of dispersion and homogenization, have a simple constructive solution are bead mills. When grinding titanium dioxide over a period of 0 to 30 minutes, the power increases from 205 to 209 W. The temperature of the suspension is from 21.9 to 23.4 °C, the density increases from 889 to 1176 kg/m3, and the particle size decreases from more than 100 μm to 10 μm. The most intensive grinding in the first 5 minutes of the process. When the quinacridone red 122 is grinded, the power is increased from 205 to 210 W, the temperature of the suspension is from 22.4 to 24.3 °C, the density increases from 870 to 952 kg/m3, and the particle size decreases from more than 60 μm to 2 μm, while the most intensive grinding occurs in the first 5 minutes of the process. Conclusions. Among the recommended installations, the most optimal and productive are bead mills. It is recommended to carry out the grinding process on the bead mills periodically with the circulation of the suspension with the obligatory cooling.